How to solve the problem that BMW ICOM A2 A3 host can’t be connected New

  • -

How to solve the problem that BMW ICOM A2 A3 host can’t be connected New


After the BMW ICOM host is connected to the car via a 16 PIN connector, and the other side is connected to the computer via a network cable. Your OBD2 Scanner BMW ICOM lan and system lights will light up. As follows:

But at this moment,the host can’t be found in the computer.As follows:

When meeting the problem,please update your
30% Discount Products BMW ICOM firmware as the following method:
1.Please connect BMW ICOM to the computer with network cable and power on the BMW ICOM with a 12V power adapter.
2.Open the website address IE browser, username:root password: NZY11502.
3.Click the “update firmware”,it will show ICOM firmware version information.
4.Choose the file ICOM-BootImage-01-11-01.bin,set image type to SYSTEM,click “Send the file”.
5.When shows “Write the image file to the flash?”,click “Yes”,then ICOM light turns red.
6.When shows “The SYSTEM IMAGE update was successful”,click “Update Firmware”.
7.Choose the file ICOM-ApplicationImage-01-15-01.bin,set image type to APPLICATION.Click “Send the file”.It will takes a few minutes because of a little large file.
8.When shows “Write the image file to the flash?”,click “Yes”,then the ICOM light turns red for the second time.
9.It is all normal,click “reboot”.

  • -

BMW E90 Coding with NCS Specialist Computer software

In an effort to use the cable in the BMW automobile which I purchased a although ago, I started the basic diagnostic program INPA and succeeded to connect with the vehicle.

The BMW Diagnostic Tool INPA plan is utilised for diagnostic purposes. It can be not utilised to adjust the setting worth in the car. It’s named NCS Expert.

I attempted to run ?

But I did not get a sense of how you can use it, so I watched the videos uploaded to YouTube and captured a single by one particular ?

Note that in the event you connect the cable towards the Auto Scanner Tool on the automobile, the cable LED will light up and then the light will go out.

You could run ncs expert straight away devoid of running ?

After you run the system, it’ll run as it looks like the picture beneath ?

1. Run the plan


2. Choose File -> Load ProFil


3 Select Expertmode (far more profiles may very well be readily available based in your installation)

4. Select Edit Profile


5. Enter Password ” repxet “


6. Click the Car-Keymemory button (reduce left)


7. Soon after checking Car-Keymemory activ, click OK button



8. Click the FSW / PSW button (bottom appropriate)

9. Right after checking FSW- / PSW-Trace, FSW- / PSW-Manipulate with FSW_PSW.MAN, click OK button


10. Click the consistence check button (verify ok popup window)


11. Click the OK button


12. Click the VIN / ZCS / FA button (F1)


13. ZCS / FA f. Click the ECU button (F3)


14. ECU choice just after deciding on vehicle CHASSIS (Capture photograph based on E46)


It is possible to select E90 as CHASSIS: E89, ECU: CAS.

BMW-E90-Coding-with-NCS-Expert-E90_1 BMW-E90-Coding-with-NCS-Expert-E90_2

Information displayed when choosing the vehicle code and ECU ?-


15. Press the Back button (F6) to visit the key screen


16. The worth is in the get coded, JOBNAME component, which was not displayed initial.

17. Click Approach ECU button (F4)
18. ECU module choice (distinctive from car kind)


[Module Names]

ABG ¨C Airbag Module

AEWS ¨C Immobilizer

AKMB ¨C Instrument Cluster

ALSZ ¨C Light Switch Center

BTM ¨C Passenger mirror module

CVM ¨C Vert Module ¨C do not touch this, apparently it?ˉs sensitive


FTM ¨C Driver rearview mirror module

GM5 ¨C ZKE ¨C Central Physique Electronics

GT ¨C Navigation


LWS ¨C Light Switch

RAD ¨C Radio

RLS ¨C Rain Sensor

SM ¨C Seat Memory

UEB ¨C Rollover Sensor

19. Choose GM5 module and confirm that GM5 has been changed to get coded region.

¨C Choose GM5 as a sample to adjust Auto Central Lock setting


20. Click the Adjust job button and pick CODIERINDEX_LESEN


21. Click the Study ECU button (F4).

BMW-E90-Coding-with-NCS-Expert-24 BMW-E90-Coding-with-NCS-Expert-25 BMW-E90-Coding-with-NCS-Expert-26 BMW-E90-Coding-with-NCS-Expert-27 BMW-E90-Coding-with-NCS-Expert-28

Coding ended and NETTODAT.TRC pop-up window is closed


22. In the explorer, check the generated file in the path “C: \ NCSEXPER \ WORK” (FSW_PSW.TRC)

BMW-E90-Coding-with-NCS-Expert-29 BMW-E90-Coding-with-NCS-Expert-30
Open the FSW_PSW.TRC file within the edit program like Notepad, edit the preferred portion, and save the extension as MAN.

¨C This component can use plan like NSC Dummy, BMW Coding Tool


24. Choose SG_CODIEREN in Alter Job



25. Select Execute Job

BMW-E90-Coding-with-NCS-Expert-34 BMW-E90-Coding-with-NCS-Expert-35 BMW-E90-Coding-with-NCS-Expert-36

If you’d like to organize it roughly, you’ll want to extract FSW_PSW.TRC file and save the file extension as MAN.

As well as the process of putting the modified files into the automobile ?

It appears like this really is going to take place ?

As soon as I get the time, I will connect to my vehicle (E90) and make an effort to extract the FSW_PSW.TRC file related to Angel Iman DRL use ?

You simply have to have to know what ECU module to pick ?