Best OBD2 Scanner for 2018

  • -

Best OBD2 Scanner for 2018

There are few things in this world that are more annoying than when the “check engine” light pops up on the dashboard of your car. Not only is your engine running into problems, but you don’t even know what problems it’s running into.

For those that are less inclined in the mechanics of an automobile, this can pose a real conundrum. In most cases, it results in you having to bring your car into a mechanic just to figure out what the problem is. Obviously, this can be a waste of both time and money.

However, there is a device that will allow you to find the source of your “check engine” woes. This device is an OBD2 car scanner. There are quite a few OBD2 Scanner currently on the market, and you want to make sure that you choose one that’s of high quality.

1.2018 New LAUNCH X431 iCarScan Auto Diagnostic Tool Full Systems For Android/IOS With 10 Free Software Update Online



Launch iCarScan Obd2 Scanner:
1. Multi-Language: English,German, Spanish, French,Korea,Russian,Portuguese
2. Build-in bluetooth, easily connects with Android/ios smartphone
3. 10 free brand of software for your selection: You can free to download any 10 software( including car software and special functions). If you need more other softwares, pls buy it from APP store.
4. Full systems and complete function dignosis for the most extensive coverage of OE-level diagnostics
5. Widest carline software coverage: Support proprietary protocols of over 70 car manufacturers and 2, 500 car models;
6. Support multiple special function software and actuation tests incl.Oil / Service reset, ABS bleeding, IMMO & key programming, throttle body adaptation, brake pads,steering angle reset,battery matching, DPF regeneration,Injector coding
7. Intuitive interface and easy to use

2.Piwis Tester II V18.100 with CF30 Laptop for Porsche



Piwis Tester II with CF30 Laptop For Porshe
1. Software Version: 18.100
2. Laptop: CF-30 (Second Hand)—Software is inside the Hard Drive. No need Installation
3.Support Languages: Russian, English, French, Spanish, Italian, German, Portuguese, Japanese, Chinese, Dutch
4. Update Method: By CD or HDD (One Year for Free, It can not be updated online. 200USD for one time update after one year.) Software contains operating system win XP only. you just need to insert into your computer and use it.
5. Requires Online Modules: (F BCM R BCM DME ELV SRS KEY)
6. Bluetooth,GPS and Navigation Function are available. But you need to pay for the authorization of them.
7. Support Key Programming function,cost 210USD per time ( you need consult our customer sevice first with the type and year of your car)

3.Free shipping 2018 CARFANS C800 Heavy Duty Truck Diagnostic Scanner with Special Function



CAR FANS C800  Feature:
1.Wide Vehicle Coverage: CAR FANS C800 support 35 Heavy duty brand, 21 BUS Brand, 16 Passenger car Brand, 32 Machinary vehicle brand and 46 ECU System, almost cover all brand heavy duty vehicles in market
2.Powerful function of software: C800 is fully optimized based on the OEM scanner, which enhances the comprehensive diagnostic capability of the diesel vehicle. Some of the functions are based on the advanced technology accumulated by the R & D team for many years. The main diagnostic functions include reading the version information, reading/clearing the fault code, actual values, actuators, advanced function
3.Fashionable design of hardware: 7 inch 800 x 480 touch screen, super light main unit, is easy to hold and operate. ARM9 CPU with 4GB memory, the software operation is faster than similar tools
4.Advance Functions: Adjustment/Settings, Function Test, Special function, calibration.
5.Online Updating: Log in the official website ( download and install the C800 intelligent diagnostic device upgrade client software, the device SD card through the card reader plug in the computer USB interface to complete the device software upgrade.
6.ECU Programming & Coding for 5 Brands
7.2 Years Free Update Online
8.Support 24 Languages:English,Japanese,Korean,French,Spanish,Portuguese,Italian,Russian, German,Polish,Romanian ,Finnish, Hungarian,Swedish.

4. Original Autel MaxiSys Pro MS908P Wifi OBD Full System Diagnostic with MaxiFlash Elite J-2534 programming



Top 4 Reasons to Get Maxisys Pro 908P:
1. Software Version: Every Car Model Software Has A Different Version.
2. Wi-Fi Technology: The VCI connects wirelessly to the main unit with Long-Range Class 1 Bluetooth
3. Update:  2 Year Free Update Online, Contact our sales, you can add 1 more year free update,after 2 years,900USD/year.
4. Shipping by DHL All Around the World, 3-5 Days Delivery

5.Autel Maxisys Elite (Upgraded Version of MS908P Pro) Diagnostic Scanner with J2534 ECU Programming Extensive Vehicle



Why buy Autel maxisys elite:
1.Genuine Autel top scanner , 2years free update online,after 2 years,1000USD/year.
2.The top diagnostic techniques, support almost all car brands , workshop Standard diagnostic equipment
3.not only easy to use by own diagnostic software , but also works on OEM software like xentry odis do special setting
Language: only support english and Spanish now

If you any questions, contact

  • -

Guide to BMW CIP Programming with MaxiSys Pro

Guide to BMW CIP Programming with Maxisys Pro

1. BMW Programming Notes
– Connect an Autel or BMW approved battery charger to the vehicle, and ensure battery voltage is between 13V and 14V.
– Turn off all the electrical equipment, such as air conditioner, headlamps, turn signal lamps, wipers, etc. Unstable current will abort programming.
– Turn off wipers or cleaning system. Wipers may be active during programming, so please make sure there is enough space.
– Please check all the control units are installed and function properly before programming.
– Troubleshoot or clear DTCs of the vehicle before programming.
– Please set the correct date first. It will be recorded into the control units during programming and coding.
– Do not turn the ignition off during programming and coding unless specifically instructed to do so by MaxiSys Pro.
– Do not activate or move any part of the vehicle, such as windows, doors, the steering wheel, seats, buttons and other adjusting knobs. Failure to do so may abort programming.
Note: This document is built up based on BMW V3.00. It only applies to BMW V3.00 or later versions.

2. Entering CIP Main Interface
Tap ‘CIP (Coding, Individualisation, Programming)’.


For vehicles performed CIP function with Autel Scanner MaxiSys Pro for the first time, please refer to 2.1 Initial Entering CIP.
For vehicles performed CIP function with MaxiSys Pro before, MaxiSys Pro will save the previous session automatically, and a prompt message will pop up to confirm whether to use the saved session. Please refer to 2.2 Re-entering CIP for additional information.
Note: MaxiSys Pro can only store up to 5 vehicle sessions. It will prompt you to remove some unnecessary ones if there are more than 5 sessions. Please refer to 2.2 Re-entering CIP.

2.1 Initial Entering CIP
MaxiSys Pro will read the current vehicle configuration information from CAS and LM/FRM when entering CIP for the first time, so CAS and LM/FRM cannot be replaced at the same time. Vehicle information will be shown as figure 2.2. You can
scroll through the list by sweeping your finger up and down to see more information.


Tap ‘Edit’ to revise vehicle configuration information and the related interface will be shown as figure 3. You can scroll through the list by sweeping your finger up and down to see more information.
Note: To avoid the issue that the vehicle cannot work properly after revising the configuration information, it’s recommended to note down the current configuration information.


Tap ‘Add’ or ‘Remove’ to do the corresponding operation, and then tap ‘ESC’.
You will be prompted to confirm the revised configuration information, as shown in figure 4.


Tap ‘Yes’ to save the information, or tap ‘No’ to cancel the changes. The above revised configuration information will be valid only after performing corresponding programming or coding.
Then MaxiSys Pro will communicate with all control units. This step will take several minutes, which is based upon vehicle specifications, as shown in figure 5.


MaxiSys Pro will ask whether the control units have been replaced, as shown in figure 2.6. If the control units have been replaced, tap ‘Yes’ to select the replaced control units. Alternatively, tap ‘No’.


MaxiSys Pro will read integration level (I-level) from vehicle after performing all the above procedures. If the integration level could not be read from vehicle, manual input is required, as shown in figure 7.


If the vehicle integration level is very new, the following message in figure 8 may appear on the screen.


This shows that the vehicle integration level is newer than the one stored in MaxiSys Pro, and programming function is not recommended.
MaxiSys Pro will then read related information from each control unit to confirm whether it needs to be replaced or upgraded. After that CIP Main Interface will be shown. Please refer to 2.3 CIP Main Interface for detailed information.
2.2 Re-entering CIP
If CIP function has been performed before on the vehicle, MaxiSys Pro can save the previous session which records the configuration information. When MaxiSys Pro re-enters CIP, a prompt message will pop up to confirm whether to use the saved session, as shown in figure 9.


Tap ‘Yes’ to continue the saved session without establishing communication with vehicle again. This will realize fast access to CIP. Tap ‘No’ to reject the saved session, and MaxiSys Pro will establish communication with vehicle just as the procedure in initial entering CIP. Please refer to 2.1 Initial Entering CIP for additional information.
It is recommended not to use the session saved long time ago for the actual information of the vehicle may have changed.
MaxiSys Pro is set to only store up to 5 vehicle sessions. It will prompt you to remove some unnecessary ones if there are more than 5 sessions, as shown in figure 10

Tap ‘OK’ and a list of vehicle record will display. You can select the sessions to be removed, as shown in figure 11.

Select the sessions to be removed and tap ‘OK’. The message below will display on the screen, as shown in figure 12.


Tap ‘OK’ to remove the selected sessions. Then re-entering CIP is required.

2.3 CIP Main Interface
CIP Main Interface typically includes the following items, as shown in figure 13.


– Initial Report
Displays the information of control units to be replaced or upgraded and the estimated upgrade time.
– Vehicle Details
Displays vehicle configuration information.
– Programming/Coding
Performs programming and coding. Please refer to 3. Programming/Coding for additional information.
– CAR/KEY Memory
Performs personalized setting.
– Programming Follow-up Routine
Displays a list of special functions to be performed after programming and coding.

3. Programming/Coding
Programming/Coding interface typically includes the following items, as shown in figure 14.


– Determine Measures Plan
Lists the upgrade plan automatically calculated by MaxiSys Pro.
Please refer to 3.1 Determine Measures Plan for additional information.
– Complete Update
All the ECUs available to programming/coding are checked by default.
Please refer to 3.2 Complete Update for additional information.
– Selective Update
Manually selects the ECUs you want to perform programming/coding.
Please refer to 3.3 Selective Update for additional information.
– Control Unit List
Displays all the control units, and you can perform diagnosis, programming,
coding, and special functions to the specific ECU. Please refer to 3.4 Control Unit List for additional information.

3.1 Determine Measures Plan
Determine Measures Plan shows a list of tasks for the current vehicle set by MaxiSys Pro, as shown in figure 15. You can scroll through the list by sweeping your finger up and down to see more information.


Tap ‘Execute measures plan’, and a prompt message of turning off engine and switching on ignition will pop up on the screen, as shown in figure 16.

After confirming that engine is turned off and ignition is switched on, tap ‘OK’. If MaxiSys Pro needs to be connected to the Internet to download configuration file, the following message will display.


Disconnect MaxiSys Pro from vehicle (not a must), take Autel Maxisys Pro MS908P to the place with Internet connection, tap ‘OK’ after the network is connected, and then MaxiSys Pro can download configuration file from server, as shown in figure 18.


When download is complete, the following message will display.


Please check MaxiSys Pro is connected with vehicle first, and then tap ‘OK’ to execute the plan. If there are programming tasks, the control units in programming will show the progress in percentage, as shown in figure 20 and figure 21.
A prompt message of turning off ignition and removing the key from key slot will pop up when performing CAS programming, as shown in figure 22.


Turn off ignition and remove the key, and then tap ‘OK’ to start CAS programming.
After CAS programming is complete, switching on ignition is required, as shown in figure 23.


Switch on ignition, and tap ‘OK’ to complete CAS programming.
MaxiSys Pro will generate a final report after executing the plan. You can scroll through the list by sweeping your finger up and down to see more information.


The information after executing the plan is available in this report, including the status of a single task, which can be viewed in the Status column.
Tap ‘End session’ to exit CIP, or tap ‘Continue session’ to continue programming. After tapping ‘Continue session’, MaxiSys Pro will read configuration information from vehicle again and communicate with each control unit. It will take several minutes, which is based upon vehicle specifications.

3.2 Complete Update
Complete Update shows a list of control units, as shown in figure 3.14


All the control units available to programming or coding are checked by default. You can manually select the corresponding items of each control unit to make any change. If the selected control unit must be programming or coding as part of a group, MaxiSys Pro will automatically select the related control units and display their names.


Some items may not be selectable, and the possible causes are as below,
– Programming or coding is not available for the control unit
– The control unit has error or needs to be replaced. Please refer to Initial Report in CIP Main Interface for detailed information.
Tap ‘OK’ after making your selection and MaxiSys Pro will determine a plan. Please refer to 3.1 Determine Measures Plan for additional information.

3.3 Selective Update
Please refer to 3.2 Complete Update for additional information about Selective Update. Programming and coding items only for control units needing to be updated are selected by default for Selective Update, which is the difference from Complete

3.4 Control Unit List
Control Unit List displays all the control units, as shown in figure 3.16. You can scroll through the list by sweeping your finger left and right to see more information.


Tap the corresponding control unit to view the diagnostic information, control unit information, and the last programming information; to perform programming or coding; or to perform some related special functions.