Category Archives: MB STAR

  • -

How to configure Xentry Connect C5 V09.2017

2017 Xentry Connect C5 user manual: how to configure/set up MB SD Connect C4/C5 to use for the first time

Please have your XENTRY Connect MAC addresses (Wi-fi and LAN) enabled for the workshop network byyour IT supervisor/IT service provider in advance. You can read off theMAC addresses (Wi-fi and LAN) from the stickers on the devices.
26-1

Your case already contains a printed empty network questionnaire.

Please have it filled out by your IT supervisor. Important! Do notcontinue the initial startup until the questionnaire has been filled outcompletely! This will help to avoid additional work.
26-2

The latest Mercedes diagnostic software 09.2017 disk came with your MB SD Connect C5.

You can start the network configuration now.

Completely charge and turn on the XENTRY Connect.

Starting the XENTRY Connect for the first time can take up to 10 minutes.

Configuration can be started whilst both devices are still charging.

Attention! Be sure to use the correct power supply units!

Start the XENTRY Control software using the desktop link on the laptop. ConfigAssist is already open; if not,call up ConfigAssist via the “Configuration” menu.

Note! If you work with static IP addresses, you must perform theconfiguration via the expert dialog and transfer the configuration tothe XENTRY Connect via a USB stick.

26-3
Please have the filled out network questionnaire on hand:

How would you like to configure the devices?

Select one of the 3 options.

Recommended selection: “New without existing configuration data”.

26-4

Please continue following the ConfigAssist dialogs and enter the required

data from the network questionnaire.

Next, switch on the XENTRY Connect. This has already finished installing.
26-5

In the final steps, the configuration is transferred from the laptop to the XENTRY Connect. You will be prompted to interconnectthe devices using the supplied black Ethernet connecting cable.

This cable connection is required only for configuration

If configuration is successful, a green tile with the number of the Benz diagnostic tool XENTRYConnect C5will be displayed. You can now use the devices: Remove theblack Ethernet connecting cable to work via WLAN and with an onlineconnection. Then click on the green tile in order to read out the datafor ordering the StartKey.
26-6

Done!


  • -

How to tell it’s a REAL Xentry Connect C5, not FAKE

Real and fake Xentry Connect have the same look. So, how to know if your Xentry SD Connect C5 is real or not?

Real Mercedes BENZ C5 should have good design & quality. Look here:

21-1

21-2 21-3 21-4 21-5

It’s 1:1 clone of the original from the French ACTIA Company

This board is verified to work no issues

21-6 21-7 21-8 21-9
Fake Xentry Connect C5 has boards inside, the same as SD connect c4. Have a look at this:

21-10 21-11 21-12 21-13

the fake mb star c5 has nothing update

it is another Mercedes Star Diagnostic Tool SD C4 with a different look only

fake C5 adopts the same design in appearance as the genuine from French ACTIA Company

same sw, some PCB, same result as SDconnect

Only with Real SDconnect C5, you have opportunity to:

1 diagnose newest hybrid W222

2 do DoIP diagnosis coz it has an Ethernet switch, which switches the TCP/IP messages

3 get what you pay for coz you’ll have the best experience of MB diagnostic that there is a qualitative improvement in C5 hardware and software help diagnostic efficiency esp. speed and stability

The last – there are many MB STAR C5 versions, some genuine & some copy, some HQ clone & some crappy. You can check information here: http://www.obd2tool.com/goods-5186-MB+Star+C5+With+Vediamo+V050006+Engineering+Software+Plus+EVG7+Tablet+PC.html (if the C5 is like this, you may have the luck to have a real one) www.obd2tool.com is a good man of his word to trust in.

21-14
Good luck!